Copper beryllium, also known as beryllium bronze, is a copper alloy with 0.5—3% beryllium. Copper beryllium is the hardest and strongest of any copper alloy (UTS up to 1,400 MPa), in the fully heat treated and cold worked condition. It coines high strength with non …
Hose Length: 1m or 3m lengths: Pressure Rating: 2,250 psi, min. Burst pressure 9,000psi. Outer Sheath: Black, oil and abrasion resistant neoprene (CR) Inner Tube: Nitrile, Oil Resistant: Hose ID: 3/8" Reinforcement: Braids of high tensile steel wire: Temperature Rating-40 to 100C: End Connections: Spinning Threaded BSP: Code: Meets or exceeds
Description. Recommended For : High Pressure Hydraulic oil lines in appliions where the outside cover of the hose is subjected to abrasion that may cause premature failure of standard hoses.
Rubber Petrol & Oil Bowser Hose (A420) A420025. View Similar Products. High tensile steel wire braid; Note. Minimum cut length of 5 mtrs, charges apply for cutting hose. Complete hose data specifiion sheets are available upon request. Contact Dixon for …
2 Max Jack - 1/4" Hose (328'' Continuous Reel) $700.00. Add to Cart. Remove from. Compare. Compare Items. Quick view. Balflex Hydraulic Hose.
90° Universal Hose Bend - Fuel & Oil. Dayco 90° Universal Hose Bends for Fuel. Manufactured with 2 constructions depending on size. knitted high tensile strength Para-Aramid fibre to give maximum burst protection. •Sizes 8mm to 19mm are suitable for low pressure fuel appliions. Hose suitable for use with leaded and unleaded petrol
EHA500 - High Pressure Air Hose. Tube: Oil-resistant nitrile blend; Reinforcement: High-tensile steel wire; Cover: Synthetic rubber; Temp: -40°C to +93°C, (-40°F to +200°F) Pressure: 41 bar / 600 psi; H9622 - Contractors Air Hose. Tube: Nitrile (RMA Class A) Reinforcement: 1- & 2-wire braid; Cover: Neoprene; Temp: -40°C to +93°C, (-40°F to +200°F)
Reinforcement: Four (Six for 20, -24 and -32) layers of alternated, spiralled, high tensile steel wire. Cover: Black, oil resistant synthetic rubber (Neoprene-Type A). With colour coded layline. MegaTuff® Hose lasts up to 300 times longer than the standard hose during hose-to-hose and hose-to …
When an emergency situation comes up a hose pipe can be attached to these valves to put out the fire. These valves are available with a 63 mm diameter in both single and double head formation. These valves are widely used for their anti-corrosive properties, high tensile strength and longer service life.
CHAMPION BC21 HIGH TENSILE FULL THREAD UNC BOLTS & NUTS 5/16" X 1-1/2" PACK OF 5. Add to Cart. $23.00 $16.82. or 4 payments of $4.21 with Info. SKU: BC36.
High pressure and pulse resistance and long service life, Ryco steel wire spiral hydraulic hose fully meets the needs of high-end hose users such as heavy machinery and equipment manufacturers. Ryco hydraulic hose is guaranteed for use in the construcion, mining, agriculture, oil & gas and other industries with high performance.
Flexible Hose Product Specifiion HIC Manufactured UNIVERSAL Brand. Universal Flexible Hoses ensures burst-proof hydraulic pneumatic pressure flow, in a way, hose inner lining rubber tube is made of compounded synthetic rubber, braiding material used is either of textile dipped nylon yarn or woven ply cotton fabric and or galvanized iron wire for operating pressure rating needs, outer hose
Oil Equipment is used for the process of production and exploration of oil and gas or generation of any kind of upstream energy. This equipment is considered as one of the most important parts for oil and gas services. It also includes tools whose purpose is to drill and excavate the oil and gas, management of energy data, finding and loing the sources of energy, constructing and completing
When the job requires tight bends, flexibility and abrasion resistance, this high-pressure service hose steps up to the task. Using a nitrile inner tube and two-wire, high-tensile steel reinforcement, it can handle 5,800 psi (31 MPa) flows of petroleum- and water-based hydraulic fluids. XR16SC High-Pressure Hose.
BOP Hose Construction. Tube: oil resistant synthetic rubber; Reinforcement: 4 or 6 high tensile steel wire spirals; Cover: oil and fire resistant synthetic rubber (5-minutes at 1300°F); Operating temperature: -40°C to +121°C (-40°F to +249.8°F); Operating pressure: 5000psi (35MPa); Hose diameter: 6mm to 51mm; Hose length: up to 90ft. Product egory
Reinforced with high tensile synthetic textile and steel helix wire. Covered with abrasion and weather resistant synthetic rubber. Appliions: General purpose Agricultural Irrigation Construction Camlock fittings (quick connect couplings) allow for quick, secure connections of hoses to tanks or other hoses.
Tube: black NBR (RMA Class A) – oil mist resistant Reinforcement: high tensile steel wire braids. Cover: yellow SBR/NBR – abrasion, ozone, hydrocarbon and flame resistant – pin pricked. Appliion: high pressure compressed air designed for heavy duty mine and quarry appliions where long service life and maximum safety is required.
M405 – MAXFLO Extra H/Duty Petrol & Oil Suct/ Delivery. Appliion: An extra heavy duty petrol and oil suction and discharge hose for higher pressured appliions. Tube: Black NBR Blended Rubber. Reinforcement: Dual High Tensile Steel Wire Helix and a High Tensile Synthetic Braid. Cover: Black EPDM/NBR Blended Rubber with a Red Stripe. Temp:-20°C to 70°C
Each Cylinder i s individually Oil Tested at the Factory and c omes complete with a Clevis at each end, WARNING: Hydraulic cylinders without a hose burst valve, pilot operated check valve or counter balance valve directly mounted to the cylinder will not meet Australian Standard AS1418.8, nor occupational health & safety rules.
2 Wire Hydraulic Hose 2SN SAE 100 R2T [TFD0021] - Construction: Tube - Oil resistant synthetic rubber. Reinforcement - Two high tensile steel wire braid. Cover - Abrasion and weather resistant synthetic rubber. Typical Appliions: High pressure hydraulic lines. Features: Weather resistant, durable, smooth bore, good abrasion and rot resistance.
Our high pressure hoses are manufactured by building onto an inner core of thermoplastic material, several layers of reinforcement, typically high tensile steel wires. An outer cover, which is generally Polyamide or Polyurethane, is co-extruded over the built-up hose layers to provide a tough, chemical- and wear-resistant outer coating.
SFFECO Fire Fighting hose is suitable to use with fixed fire fighting systems like fire hose reels. It''s flexibility helps to roll or handle the hoe easily. Material used for inner lining and cover of hose is plasticized PVC compound and high tensile textile polyester yarn is …
uhp hose ph902–2 spirals of high tensile steel wire ph902p–2 spirals of high tensile steel wire, 1 braid of steel wire ph902q/ph902ql/ph902qz-4 spirals of high tensile steel wire, 2 dense and 2 open layers ph903–2 spirals of high tensile steel wire, 1 braid of g.i steel wire ph904–4 spirals of …
one wire hydraulic hose. sae 100r1at/iso 1436/ en 853 1sn . tube : oil resistant synthetic rubber. reinforcement : one high tensile steel braid (1b) cover : abrasion, ozone and hydrocarbon resistant synthetic rubber. appliion : high pressure hydraulic lines, fuel oil, antifreeze solutions, air and water.
Weight w/oil TWP55-50-220-01 Single Tool 11.5 @ 7 bar 0.9 @ 700 bar 9.5 8.4 435 241 460 34 RWP55 Single Tool 7.6 @ 7 bar 0.9 @ 700 bar 9.5 8.4 450 280 483 44 TWH20-VIC • 1/4” high pressure polyurethane hydraulic hose with polymide core reinforced by two spiral layers and two open spiral layers of high tensile steel • 4:1 Safety Factor
Get superior, reliable service to your liquid transfer appliions with Water Master industrial water hoses from Gates. Gates Water Master PVC hoses are designed for heavy-duty, high pressure suction and discharge, while the Water Master and PVC Layflat efficiently manages mining, construction, agriculture, marine, and other industrial discharge appliions.